bozoph Posted December 1, 2012 Share Posted December 1, 2012 i built a purge chamber for bho. ill be trying it out soon. it was very easy, all you need is a brake bleeder and a sealed container 5 Link to comment Share on other sites More sharing options...
bozoph Posted December 1, 2012 Author Share Posted December 1, 2012 the brake bleeder was 20$, the jar and glue i had. it took all of maybe 5 minutes to make Link to comment Share on other sites More sharing options...
gonzosghost Posted December 1, 2012 Share Posted December 1, 2012 Nice Bozoph! I'm partial to a bit of DIY so will try this out for sure thanks for the tip dude Link to comment Share on other sites More sharing options...
bozoph Posted December 1, 2012 Author Share Posted December 1, 2012 i threw a marshmallow in their for giggles, then depressurized it. the marshmallow puffed up to twice its size. when i released the vacuum the marshmallow shrank down to half its original size. so there was definitely air removed from the marshmallow. proving that a vacuum purged hash will have way less solvant left in it Link to comment Share on other sites More sharing options...
lamsbread Posted December 1, 2012 Share Posted December 1, 2012 Nice one Boz, good to see a bit of DIY. A warm water bath or a coffee pot warmer will help liquify the BHO allowing gas escape.Can't wait to see your results.Will you use a dish/lid etc to hold the oil or will you place it directly in the jar?Peace broLams Link to comment Share on other sites More sharing options...
bozoph Posted December 1, 2012 Author Share Posted December 1, 2012 the oil will be in a dish for purging Link to comment Share on other sites More sharing options...
Dust Posted December 1, 2012 Share Posted December 1, 2012 very nice DIY bozoph!! for sure if it works i'll make one for my future extraction Like tok said let us know how it works Thanks for sharing Link to comment Share on other sites More sharing options...
MissKittyKat Posted December 9, 2012 Share Posted December 9, 2012 Just curious I was told and have read that the $20 break pump wiill not be enough psi to fully get all the butane out. From what I could see in your pictures it only goes up to 30. It should be at 32 or 36 for proper purging to occur. This is why some people go right to the electric pumps because the hand pumps take alot to get to 32 or 36. The cheap ones don't get all the butane out because you are only geting into the 20's.This is what I have read and heard. I didn't mean to rain on your parade but I just want to make sure people know that if you the proper pressure to purge correctly 32 to 36Hand pumps that cost $20 bucks dont have the pressure needed. The hand pumps that will work are usually 50 to 80 bucks Like this one in the pic below...it is slightly bigger then the 20 dollar ones..,I am sure the smaller one will do the job some what but this is only what I have read and discussed from some concentrate fiends.. Link to comment Share on other sites More sharing options...
bozoph Posted December 10, 2012 Author Share Posted December 10, 2012 sorry but look at the specs on that electric pump u posted its no strongerElectric Vacuum Pump will attain and hold a vacuum of 25-29"Hg. Perfect for large scale projects.http://www.extractionexperts.com/Products.html 1 Link to comment Share on other sites More sharing options...
heathenshashoils710 Posted February 12, 2013 Share Posted February 12, 2013 Bozoph, I used that same setup for months! It works great for small at home runs and you are right about your hg notes above. Full vac is 29.5Hg while rocking this EXACT setup I could only get mine to about 27.5-28 Hg but w/ all the pumping and the hours over heat, I will tell you you can get a very clean and stable product using this system. Link to comment Share on other sites More sharing options...
heathenshashoils710 Posted February 12, 2013 Share Posted February 12, 2013 sorry miss kittycat but thats how a vacuum works if your gauge says anything above 30 it is wrong. Invest in a new pump and always remember to get the Tane out! happy dabbing! Link to comment Share on other sites More sharing options...
adi Posted March 4, 2013 Share Posted March 4, 2013 awesome ideas Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now