Hey guys this is a GHSC run. Four strains, powder feeding and PK booster from the great GHSC. Super Bud Jack Herer Big Bang Super Lemon Haze In 3,6L fabric pots. Unfertilized peat and coarse vermiculite. 40w exhaust fan 15w circulation fan (X2) 8-220w dimmable DIY COB LED (4x citizen clu048 1212). Great new light for some great new strains. This is part of my search for the new favorite strains in my grow room. The big bang and super lemon haze are free promotion seeds and both had bad germination. So instead of the planned 20seedlings only 15popped. So in a panic I cloned my quick flowering mothers and hope to add these clones to the flowering room a week or two later then the seedlings. This is a classic SOG style grow with no veg and many small plants. I hope they will fill out the grow room nicely with many tight colas.

Hi Here is my plan Medium promix plagron straight wiht a layer of coco /perlite for the drain at bottom of pot +_ 5cm Ph down whit lemon or lemon kick (plagron) Grow under 400w mh flower 600w hps For the rest i just use the bio feeding i was hesitadet for myhco but no money to buy it and is a all in formul so maby some yucca extract for spray wiht anhencer en for soil if it dry but i not buy it for the moment biochar looks goed to but not this time i normarly not use 2 tent thats to much électriciti but i realy want to do the contest i think to start for this week-end bye ✌

Hello everybody, I hope this is the right forum for a topic like this. Im not a marihuana God with 30 years of growing experience (not yet ) and a knowledge like Ed Rosenthal, and cause of this Im searching for opinnions, experience and knowledge of different people. But The MarihuanaGrowingHandbook from Ed Rosenthal is an old friend of me which accompanied me since a few years, and i got some experience with growing marijuana under HPS and LED, and helped a few people with their startink and knowledge problems. I hope i can talk with people about their experience with female seeds from GreenHouseSeedsCompany, because 2-3 years ago i definetly wanted to test some nice landrace strains and some strains from GHSC, cause this company looks kind of friendly and about good quality. Since I baught some Arjans Haze Nr.3 and Himalayan Gold and tried germinate them I lost all my good thinkings about GHSC. 1 of 6 seeds ( 3x AJ3, 3xHG ) germinated, and that was like a beat in my face, I had never problems with germination, even after a few months in the refrigerator. After a few hours in the www i got superficial knowledge and a few curios stories about GHSC and thier formerly and new breeder. Now I hope some people can share her experience with me/ us and this will be a interesting thread. Greetings from a human beeing somewhere in nowhere.:)

Hello to the Green House Seed Co. Crew, Community and all the hard working men and woman of this stoked out industry!! It has been roughly a year since my last journal posted here! This is going to be another fun round! Currently there are two great seeds that were germinated and started! Caboose! This is going to be an organic soil with compost teas for feeding and One being transferred to a solid indoor ebb and flow hydroponic application that is of my own production. Lots of stoke and excitement going on over here and I am very happy and humbled to be able to share my techniques, grows and info to the great community here! Looking forward to bringing this to you with maybe some kool things you have not seen or really payed attention too....? Thanks for taking the time to scope things out! Saludos! MultiTech!

OK, so I haven't seen this before, I've always thought it was necessary but didn't realise it was already being done and so incredibly properly. I believe this facility also take deposits from multinational companies with an interest in the preservation of seed stock from around the world. I am sure GHSC and Strain Hunters keep Mums and seeds in controlled storage, but must live in fear of loss, damage, spoiling or government destruction. I seem to remember a story about some of Arjans parent stock being destroyed in Switzerland?? (May be myth). Anyway, check out the video below, I hope this is of interest to Franco and Arjan. http://edition.cnn.com/videos/world/2015/10/22/norway-doomsday-backstory-arwa.cnn

Hi Brothers & Sisters I have decided to do another SSH from GHSC, i love this starin and have had nothing but success with it in the past. I'll be using a 100w LED COB style for the grow cycle on 18/6hr with a Wilma Big 4 Pot System. 400W HPS for the flowering stage GHSC Long Feed Clay pebbles for the medium Tri-meter to keep an eye on Ph, Temp & nutrient levels In-line extract fan with carbon filter Small desk fan Tubular heater and room stat to help stabilize temps Aero-pot for the early growth after germination Currently germinating been 2days since adding seeds to tap water Ph6.9, I have never germinated in Ph5.5 More updates will follow in a couple of days or maybe sooner.

hey guys i was wondering if this little baby is going to be fine or not?? hope somebody recognize this weird deformities. here are some pics.

The “learn from your mistakes” grow!! – 28 days from seed This grow has been a rough one from the start with a decent amount of my own mistakes and various mishaps, on top of being swamped with school and homelife, and that has meant that this crop has not had nearly the attention it deserves and has definitely suffered. As you will see from the pictures, these plants are definitely not where they could be at this stage for a number of reasons that are in the details of the journal. I just hope that I learn from this rough beginning and don't repeat the mistakes that are in my control again. That said, you will notice a very strong Super Lemon Haze that I f’ed up FIM’ing (I know, how do you screw up a FIM?), a strong El Nino, and then in the rear a Trainwreck and a second Super Lemon Haze that both have had a really rough start but have seen much improvement since transplant into non compromised soil (read further ahead in the journal if interested in the moldy Pro Mix!). Even though not a contest I’ve still kept track when I can of what has been happening for my own sake, and for anyone who actually enjoys the often boring dirty details. Please don’t follow exactly what I’ve done, as I said and want to repeat, I made lots of mistakes this time around and I hope that others can learn from them!! There are not many pictures yet, I will pick up the pace on those once flowering has set in. Speaking of flowering, haven’t 100% decided how much longer to veg them, I definitely want the roots to start to fill the 23 L pots before I switch em over though, so at least another 1 or 2 weeks. This time will also allow them to catch up to where they should be. I may have to do some bending and training of the bigger SLH as things progress. Enjoy the few pictures and the tons of details (as always ) for those interested. I will take more pictures of course as they get bigger and into flower..not much to see right now Peace ** IMPORTANT** - PPM's MEASURED AND STATED USING THE 0.1 EC = 70 PPM "TRUNCHEON" CONVERSION Seeds (Surviving ones): 2 x Super Lemon Haze 1 x Trainwreck 1 x El Nino Growing media: Jiffy™ Peat starter pots 3.5 L pots – Pro Mix HP/Grodan Growcubes/Hydrotron clay pellets 23 L pots - Pro Mix™ High Porosity/Grodan™ Growchunks/Hydrotron™ clay pellets @ approx. 40/40/20 mix Lighting: Early Vegetation: 18/6 with 28W Sunshine Systems™ LED’s + Sunblaster T5 fluorescents Once established & Flowering: 18/6 with brand new 600W Hortilux super HPS bulb (more blue in spectrum) enclosed in a cool tube reflector, plus 4 x LEDS Ventilation: Intake (once tent is closed)- 4 inch (10 cm), 176 cfm (300 M3/hr) Typhoon™ inline fan with a Mountain Air carbon filter attached on the intake end to provide some protection against fungi or bacteria etc. from entering the tent. Extraction – via a 6 inch (15 cm), 280 cfm (475 M3/hr) CK™ inline fan with Mountain Air filter Water, Nutrients & Additives: Transplant: Botanicare™ ZHO (Rhizosphere root inoculant w/trichoderma & mycorrhizae) Water & Nutrients: I use the full line of GHSC Powderfeed as a base nutrient then use additives which I feel help in specific ways and compliment the PF. Full strength additives are almost never used, and the plants main source of nutrition is the PF. Vegetation - R/O (reverse osmosis) water + GHSC™ Mother’s Powderfeed as a base nutrient + Botanicare™ Cal-Mag Plus (required when using reverse osmosis water) + Advanced Nutrients B-52 + DNF™ Enhance (pine oil) + DNF Potassium Silicate Flowering – R/O water + GHSC Short Flowering PF (El Nino); GHSC Hybrid PF (Trainwreck); GHSC Long Flowering PF (Super Lemon Hazes) + Cal-Mag Plus + Advanced Nutrients B-52 (during weeks 3 – 6 of flowering + DNF™ Enhance, Advanced Nutrients™ Overdrive, DNF™ Carbo Logic + Advanced Nutrients Sensizym + DNF Potassium Silicate Boost Buddy CO2 boost bag – Trying this out instead of the CO2 pads as it is much cheaper and simpler, but I am doubtful as to how well it will perform. 18/10/13 @ 7:30 pm soaked beans: 2 x Super Lemon Haze, 2 x Trainwreck, 1 x El Nino Water: Reverse Osmosis + a few drops of Cal-Mag Plus to enable measurement of pH ppm = 140 pH’d to 6.1 w/toothpick and pH Down 19/10/13 @ 7:30 pm - Planted in 230 ppm/0.32 EC (r/o + cal-mag plus) soaked peat pellets @ 5.6 pH Dome fully closed for maximum humidity, temperature @ 26.5°C 21/10/13 Added seedling CO2 pad Leaving the light on to add heat until 1st baby sprouts then I will set the timer. @7:30 pm – 48 hours after planting 1 slh & 1 TW have sprouted 22/10/13 Woke this morning to find the 2nd SLH sprouted fully; waiting on the 2nd TW and the EL Nino. Watering the ‘unborn’ peat pellets when necessary with 0.17 EC, pH 5.6 r/o water achieved via a little bit of Cal-Mag plus. - @ 7:30 pm: 72 hrs after planting the El Nino baby is born! 4/5 sprouted. - Watering the seedlings with r/o water + Cal-mag plus @ 250 ppm /0.35 EC, pH @ 5.5 Temp = 25.5 – 26.5 w/lights on rH = 50 % 23/10/13 The2nd Trainwreck baby sort of sprouted, grew a tiny taproot but was not healthy and would not open so in the garbage she goes and RIP. Soaking a 2nd El Nino seed for 6 hrs then going to try planting in a rockwool starter cube this time that I got off a buddy to try instead of the usual peat pellets. I’ve had good success with the peat pellets with only 2 or 3 seeds lost out of 29 (if I’m counting correctly) but have read negative things about them in numerous places and I would like to try some new ideas. Soaked rockwool cube in r/o water adjusted to 0.35 EC/245 ppm w/Cal Mag Plus, pH @ 5.6 & planted El Nino seed after a 7 hour soak. 24/10/13 Lights on enviro: Temp = 25°C rH = 40 – 45% I’ve been reading multiple places that say you don’t need any higher than 55% max to veg weed, but rH has been a little too low. I’m trying out a smaller ultrasonic style humidifier that is having a hard time keeping up, since I’ve had to return the large wick-style one I keep using twice and it’s screwed up again so this would be 3 units. They don’t handle being close to heat sources (ie. portable heaters) very well. 26/10/13 – 4th day since sprouting ***NOTE TO SELF FOR NEXT GROW!! THIS IS AROUND WHERE I SHOULD HAVE STARTED VERY LIGHTLY WITH THE POWDERFEED TO ADD SOME PHOSPHOROUS AND OTHER BENEFICIAL NUTES – ONCE MULTIPLE ROOTS SHOWED The 2 SLH, 1 Trainwreck, 1 El nino babies all are looking very healthy with multiple root tips already showing through the bottom of the pellets Mixed new feed water: r/o water + Cal Mag plus + pH down 300 ppm (0.42 EC) & pH @ 5.6 Lights on temp. = 25 - 26°C rH = 45 - 50% Lights off temp. = 22°C rH = 55% 27/10/13 Some light coloured spots developing on the 1st true leaves of the Trainwreck and the SLH#2, hopefully nothing serious. Hung and opened the Boost Buddy CO2 bag above the plants. I will see how well it works compared to the pads. 28/10/13 - The 2nd El Nino has sprouted! 29/10/13 – 7 days since sprouting TRANSPLANT – Both SLH, 1 x TW & 1 x El Nino transplanted Step 1 – Soaked Grodan™ rockwool Growcubes (smaller ones for 3.5 L pot) for 30 mins in r/o water + Cal Mag Plus @ 1 mL/L x 7 L = 7 mL ppm 280 Advanced Nutrients B-52 @ 0.75 mL/L x 7 L = 5 mL ppm 60 GHSC Mother’s PF @ 0.1 g/L x 7 L = 0.7 g ppm 120 pH: 5.6 Total: ppm 460 Step 2 – Soaked Hydrotron clay pellets in r/o water + nutes for 15 minutes and agitated a few times to wash thoroughly and clean sediment from pellets then drained Cal Mag Plus @ 0.75 mL/L x 6 L = 6 mL (EC 0.3) ppm 220 pH: 5.6 Total (EC: 0.3) Step 3 – Added dry Pro-mix HP and mixed 50/50 with Grodan rockwool Growcubes, watered to drain with: Cal-Mag Plus @ 1 mL/L x 10 L = 10 mL (EC 0.40) ppm 270 DNF Enhance pine oil @ 0.5 mL/L x 10 L = 5 mL (EC: 0.03) 20 ppm Advanced Nutrients B-52 @ 0.5 mL/L x 10 L = 5 mL (EC 0.08) 50 ppm GHSC Mother’s @ 0.15 g/L x 10 L = 1.5 g 160 ppm pH @ 5.6 Total ppm: 500 Temp: 21 °C Step 4- Lined the bottom of the 3.5 L pots with a double layer of Hydrotron pellets Step 5 - Filled the pots with soiless /growcube mix leaving room for the peat pellet/seedling and a top layer of hydrotron Step 6 - Sprinkled ¼ tsp as per directions of Botannicare ZHO root inoculant (mychorrizae, trichoderma, amino acid) in circular area where seedling was to be placed Step 7 – Cut mesh from top of peat pellets and rolled down ¼ of the way down the pellet so water penetrates and reaches root ball. Step 8 - Placed pellet in pot on top of sprinkled ZHO and filled in with Promix/growcube mix then topped with light layer of hydrotron Step 9 – Watered around pellet with same nutrient mix as Pro-mix wetting Step #3 **used about 70/30 mix of rockwool cubes to soiless this time. Added 2nd LED with T5’s hanging vertically as side lighting. The spots on the two seedlings continue to spread a little. They have lots of roots so I’m hoping they just wanted a bigger home and that the transplant helps them 30/10/13 El nino #2 is looking great in the rockwool cube, taproot is showing through the bottom of the cube. The plants already look like they love the transplant with the SLH#1 and EL Nino both reaching high for the leaves and both showing excellent growth. The new leaves on the 2 “spotted” plants look great and they also show decent growth overnight. Mixed water for El nino seedling: r/o water + Cal-Mag Plus + pH down Ppm = 300 pH = 5.6 Temp = 20 ** Note: El nino seedling water got higher ppm than the others, @ 300 ppm it’s the same as my tap water but with a different form of Calcium and Magnesium than in tap water, one much more available to the plants. 02/11/13 – Main group @ Day 11 since sprout The spotted SLH#2 is coming around the best out of the two strugglers, but the spotted TW is still smallish and struggling the most. With less healthy leaf tissue to photosynthesize I think it is holding it back. The good news is that new growth is healthy with the 2nd set of true leaves looking good, she is just on the small side for now. 03/11/2013 – El Nino is 6 days old The SLH#1 and EL Nino #1 are both thriving in their new pots and are quite large compared to the other 2, but even they even have a tiny bit of spotting on the leaf fringes. I think I might have ideas about what could have caused the problems: By day 4 I should have added a tiny bit of Mothers PF and lowered the Cal-Mag a little to add phosphorous etc. – MOST LIKELY the CAUSE AND NEED TO REMEMBER FOR NEXT GROW!! The rH was too low causing issues with uptake of calcium and magnesium MY LAZYNESS – I was mixing water and using it 48 hours later, maybe even 72 hrs once. And although it is only Cal-Mag Plus, it is best to mix fresh water every watering, at least every 24 hours. Being seedlings they deserve better treatment than adult plants and I would never premix water like that as the nutrient ions could possibly come out of solution after a certain period. I won’t do this again. Cleanliness and sterilization – nothing big, again lazy/busy in this area ie. hand washing, cleaning AND sterilizing tools etc. Things you take for granted until something goes wrong. It’s been 3 days since the main taproot showed through the bottom of the el nino rockwool cube and shes very healthy but still no other roots. I would like to see a few more poke through before I transplant them. After some reading, I should be letting the cube dry out a little more before I water it, and she is super green so no more than 220 - 250 ppm is probably good since rockwool pretty much gives up all the food to the roots with its excellent cat ion exchange properties **ALSO SEE BELOW UNDER “DISSAPOINTED IN MYSELF” ** DISSAPOINTED IN MYSELF – I forgot one of the bigger things that I learned last grow L: I noticed now that last grow the PF was started very lightly by the 4th day of growth with the Big Bang plant and I was trying to model the feedings in this grow somewhat around it..damn L The PF has phosphorous, Cal Mag plus has none. I’ve started the El Nino #2 on light PF as of today at 6 days, I hope it helps. This could be reason for the spots and issues with the 4 main seedlings before I transplanted as well, and I ‘m also noticing a bit of bluish colour which could be phosphorous deficiency. I’m staying calm, carrying on and hoping for the best. LOTS OF LESSONS TO BE LEARNED AND REMEMBERED AND I’M FEELING VERY MUCH LIKE A NEWB RIGHT NOW! Sometimes it is good to remember you still have lots to learn BUT I should have taken more time to look over my notes from my last regular photo grow if I’m gonna take the time to keep them L Mixed up 500 mL new water for El Nino – now 6 days old: Cal – mag Plus to ppm = 220 GHSC Mother’s PF @ ppm = 80 pH = 5.5 Temperature = 20 °C Lights on temp. = 25 - 26°C rH = 45 - 50% - it was around 55% for a couple of days but it’s very dry outside again. Lights off temp. = 23°C rH = 55% 04/11/2013 – El Nino#2 is 7 days old – transplant time The El nino baby has nice fuzzy multiple roots now coming out the bottom of the cube and it’s time to put her in a 3.5 L pot. I’ve again made a few slight changes to the nutrients used at this step with slightly more Powderfeed going into step #3. Step 1 – Soaked Grodan™ rockwool Growcubes (smaller ones for 3.5 L pot) for 30 mins in r/o water + Cal Mag Plus @ 0.9 mL/L x 2 L = 1.8 mL ppm 240 Advanced Nutrients B-52 @ 0.5 mL/L x 2 L = 1 mL ppm 40 GHSC Mother’s PF @ 0.15 g/L x 2 L = 0.35 g ppm 180 pH: 5.6 Temp: 20 Total ppm 460 Step 2 – Soaked Hydrotron clay pellets in r/o water + nutes for 15 minutes and agitated a few times to wash thoroughly and clean sediment from pellets then drained Cal Mag Plus @ 0.75 mL/L x 6 L = 6 mL ppm 220 pH: 5.6 Total: ppm 220 Step 3 – Added dry Pro-mix HP and mixed 50/50 with Grodan rockwool Growcubes, watered to drain with: Cal-Mag Plus @ 0.9 mL/L x 2 L = 1.8 mL 240 ppm DNF Enhance pine oil @ 1 mL/L x 2 L = 2 mL 30 ppm Advanced Nutrients B-52 @ 0.5 mL/L x 2 L = 1 mL 50 ppm GHSC Mother’s @ 0.15 g/L x 2 L = 0.3 g 200 ppm pH @ 5.6 Total ppm: **520 Temp: 21 °C ** used a little too much PF, diluted to 470 ppm with r/o **Bad news – gonna be one of those crops While transplanting the El nino#2 I noticed the smell of the ProMix was more musty than normal, and there was a bit of moisture it seemed between the outside of the bale and the package, the area that was already opened looked ok so I went ahead with it. Keep in mind this is the bale I opened about 4 or 5 months ago but I didn’t use much of it (maybe 10 L out of 109 L) and thought it would be ok to store and use but I decided it would be best to throw it out and purchase new Promix after the transplant. $32.99 isn’t worth a ruined crop. When I took it outside and cut open the entire bale to spread it out I noticed mildew or mold growing on the compacted outside of the bale L So, I basically transplanted the 5 plants into compromised Pro-Mix. Very shitty and I can only hope that the entire bale isn’t full of it. My second hope is that I used Botanicare ZHO mychorrhizae /trichoderma root inoculant at transplant and that this stuff beats out any nasty fungus that might be present. They will all get another dose in about 1.5 weeks at next transplant, as well as new Pro-Mix HP + Grow chunks. I’m also going to foliar spray the leaves with the DNF Enhance pine oil additive at half the recommended strength for foliar to start. It is specifically used to fight pathogens in the plant tissue and is supposed to be good for seedlings even. Misted the plants at lights on with/ Reverse osmosis water + DNF Enhance pine oil @ 0.7 mL/L x 1 L = 0.7 mL pH = 6.8 Temp. = 21 ppm = too low to read *Raised the LEDs up to 60 cm until the leaves were dry Added 3rd LED and set up the 2 T5 Sunblasters vertically on either side of the LEDS, also angled the outer LEDs slightly towards the centre. 06/11/13 – Main group of 4 plants are 15 days old Today is the 1st water since transplanting the main group 8 days ago. Watered Trainwreck, El Nino#1, SLH#1 & #2 each w/ 1 L r/o water + Botanicare Cal Mag Plus @ 0.9 mL/L x 4 L = 3.5 mL ppm: 260 DNF Enhance pine oil @ 1 mL/L x 4 L = 4 mL ppm: 40 Advanced Nutrients B-52 @ 0.5 mL/L x 4 L = 2 mL ppm: 50 GHSC Mother’s Powderfeed @ 0.25 g/L x 4 L = 1 g ppm: 260 Drops of Phosphoric acid (pH down) Temperature: 20°C pH: 5.6 Total ppm: 610 Plant Run-off pH Run-off ppm SLH#1 6.2 950 SLH#2 6.3 930 El Nino#1 6.3 950 Trainwreck 6.4 950 07/11/13 There hasn’ a lot of growth up top from El nino #2 since the transplant. I’m concerned that either it was transplanted a little too soon and there weren’t quite enough roots, or that the soiless peat surrounding the rockwool cube is wicking the moisture away from the rockwool cube and root ball which from what I’ve read is a common problem when transplanting from rockwool to soil or soiless. Watered rockwool cube of El Nino#2 w/ r/o water + Botanicare Cal Mag Plus @ 0.9 mL/L x 500 mL = 0.45 mL ppm: 260 Advanced Nutrients B-52 @ 1 mL/L x 500 mL = 0.5 mL ppm: 100 GHSC Mother’s Powderfeed @ 0.15 g/L x 500 mL = 0.075 g ppm: 40 Temperature: 20°C pH: 5.6 Total ppm: 400 FIM’d SLH#1 @ 5th node: She is getting tall quickly, and the El Nino is staying short and squat true to her genetics. I figure it’s time to try some new tricks and control the SLH height at the same time. I may or may not FIM SLH#2 depending on how she does. She is a little behind her sister due to her struggles at the beginning with the spots. Lights on temp. = 25 - 27°C rH = 50% - 55% Lights off temp. = 23°C rH = 55% 10/11/13 – 21 days old Last night the 600W cool tube was installed and was set at 80 cm above the plants. It was lowered to 70 cm today and they seemed to respond well last overnight. The T5’s are being used horizontally right now as side lighting to help the lateral branching develop under the big fans. The LEDS will be added soon as well. Damn cat snuck downstairs and into the tent while doing the light install, I turned around and there he was having already taken a big bite outta two SLH#2 leaves L Every single crop he manages to get a taste somehow I’ve at least positioned the T5’s to take advantage of the leaves not shading as much of the lateral growth. I learned a hard lesson about transplanting seedlings too early from a rockwool cube into soilless. The little El nino was doing absolutely nothing and I tossed her out a few days ago. She didn’t have enough roots coming through the cube and the few that did started to rot. SO it will be a 4 plant grow it looks like. I was looking at rapid rooters at the hydro store and may try them next. The owner has had amazing results he says and they can be transplanted into soiless without worrying about water being wicked from them. Watered El Nino, SLH#1 each w/ 1.5 L r/o water + Botanicare Cal Mag Plus @ 1.25 mL/L x 3 L = 3.75 mL ppm: 300 DNF Enhance pine oil @ 1 mL/L x 3 L = 3 mL ppm: 30 Advanced Nutrients B-52 @ 0.75 mL/L x 3 L = 2.25 mL ppm: 80 GHSC Mother’s Powderfeed @ 0.45 g/L x 3L = 1.3 g ppm: 340 Potassium Silicate @ 0.125 mL/L x 3L = 0.4 mL ppm: 20 Drops of Phosphoric acid (pH down) Temperature: 20°C pH: 5.7 Total ppm: 770 Plant Run-off pH Run-off ppm SLH#1 6.2 1000 El Nino 6.2 1010 11/11/13 Watered Trainwreck & SLH#2 each w/ 2 L r/o water + Botanicare Cal Mag Plus @ 1 mL/L x 4 L = 4 mL ppm: 290 DNF Enhance pine oil @ 1 mL/L x 4 L = 4 mL ppm: 40 Advanced Nutrients B-52 @ 0.75 mL/L x 4 L = 3 mL ppm: 70 GHSC Mother’s Powderfeed @ 0.4 g/L x 4L = 1.5 g ppm: 340 Potassium Silicate @ 0.125 mL/L x 4L = 0.5 mL ppm: 20 Drops of Phosphoric acid (pH down) Temperature: 21°C pH: 5.5 Total ppm: 760 Plant Run-off pH Run-off ppm SLH#2 6.3 970 Trainwreck 6.2 1010 pH has really been rising, rH also has been down to around 45%, I need to get the bigger humidifier working, hopefully it just needs a new wick. TW & SLH#2 still are not anywhere near as robust as the El Nino and SLH#1 plants. It almost looks like overfert with leaves curling under a little and a dry paper feeling, but run-off numbers aren’t that high, so possibly the pH rising with the Pro Mix gone bad. After some reading I now also know that when the Pro-Mix got damp, it activated the lime which is part of the reason the pH is climbing so rapidly. I will see how they do over the next couple days after this feed, hopefully transplanting them later in the week will help. 12/11/2013 Now that the plants have had 2 days of HID light, 2 of the LED’s were added. 13/11/2013 – 24 days old Two days since last water for TW and SLH#2 and they look much improved. With the addition of the 2 LEDS all plants were nice and erect with leaves reaching for the lights. I’ve witnessed this every grow now with the LEDS, it is amazing the response they create in the plants. Lights on temp. = 26 - 27°C **rH = 40-45% Lights off temp. = 23°C rH = 55% ** still battling low rH with the lights on. I would be happy if I could get it up to 50% lights on. Once the plants get a bit bigger and I close up the tent I’m hoping the rH rises a little. By the time I get a new wick for the big humidifier I will want the rH to be 40% J Watered El Nino, SLH#1 each w/ 2 L r/o water + Botanicare Cal Mag Plus @ 0.75 mL/L x 4 L = 3 mL ppm: 230 Advanced Nutrients B-52 @ 1 mL/L 4 L = 4 mL ppm: 100 GHSC Mother’s Powderfeed @ 0.25 g/L x 4L = 1 g ppm: 280 Potassium Silicate @ 0.125 mL/L x 4L = 0.6 mL ppm: 40 Drops of Phosphoric acid (pH down) Temperature: 20°C pH: 5.7 Total ppm: 650 Plant Run-off pH Run-off ppm SLH#1 6.2 860 El Nino 6.2 870 14/11/2013 – 25 days old – Transplant time Step 1 – Soaked Grodan™ rockwool Growchunks (BIGGER THAN GROWCUBES) for 30 mins in r/o water + (made in 2 x 17 L batches) Cal Mag Plus @ 1.25 mL/L x 17 L = 19 mL ppm: 310 Advanced Nutrients B-52 @ 1 mL/L x 15 L = 15 mL ppm: 100 GHSC Mother’s PF @ 0.4 g/L x 15 L = 6 g ppm: 350 Potassium Silicate @ 0.125 mL/L x 15 L = 1.875 mL ppm: 40 pH @ 5.5 Temp: 22 Total ppm: 800 Step 2 – Mixed in the dry Pro-mix HP, 50/50 ratio with the pre-soaked Growchunks Step 3 - Lined the bottom of the 23 L pots with a nice layer of Hydrotron clay pellets Step 4 - Filled the pots with soiless /Growchunk mix leaving room for plants and a layer of Hydrotron on the bottom and watered to drain with r/o water + Cal-Mag Plus @ 1 mL/L x 12 L = 12 mL ppm: 280 Advanced Nutrients B-52 @ 0.75 mL/L x 12L = 9 mL ppm: 70 DNF Enhance @ 1 mL/L x 12 L = 12 mL ppm: 40 GHSC Mother’s PF @ 0.25 g/L x 12 L = 3 g ppm: 260 pH @ 5.5 Temp: 21 Total ppm: 640 Step 5 - Sprinkled ¼ tsp as per directions of Botannicare ZHO root inoculant (mychorrizae, trichoderma, amino acid) on the root ball and the circular area where plant was to be placed Step 6 - Placed plant in pot on top of sprinkled ZHO and filled in with Promix/growcube mix then topped with layer of hydrotron Step 7 – Watered around plant root ball with same nutrient mix formula from Step 4. Root ball was best formed and super healthy in the El Nino, then came the SLH#1, SLH#2, and the Trainwreck last with some decent roots formed still. They were definitely not root bound, but I think in the future I can still pot up to the 23L a little sooner even if they are healthy. Added the other 2 LED’s for a total of 4. One for each plant, they’re gonna need all the help they can get this grow. The addition of the large pots has added a little bit of much needed humidity to the room with the rH staying @ 49-51% It looks like my first attempt at FIM’ing on the SLH#1 was a total fail. It looks like I cut too much of the 4th node as well which served to slow down the growth of those leaves, and I didn’t cut enough of the 5th node to produce the proper hormone response to get multiple shoots. So at least it was a learning experience, and in the end it served its purpose of slowing the upper growth of the SLH#1 to keep it manageable and allow the others to catch up, and it allowed lateral growth to increase and all is not lost. By the time they get switched to flowering she will be recovered. FOR ANYONE WHO ACTUALLY MADE IT HERE READING AND IS STILL AWAKE..CONGRATULATIONS!! YOU OWE IT TO YOURSELF TO LIGHT UP A FATTY!!

High together, I want to welcome you to my Autoflowering Grow Journal. After my White Widow (GHSC) harvest and drying procedure I put 3 Kalashnikova Auto seeds to germinate. Today the 3 seeds where put in soil, after germinating them with the Greenhouse method. (soak for 24h, then put on wet toiletpaper for 24h) The top of the pots where covered with plastic foil to create a humid enviroment. (initial root lengths when planted: about 4mm) The first medium I am using for my seeds is a premixed soil mix with perlite and low nutrition made by "ASB GREENWORLD". [N:150-500 mg/L,P2O5: 40-300 mg/L, K2O: 50-400 mg/L] My Kalashnikovas will recieve Greenhouse Powder Feeding when first growing stage is over (i guess in about 3 weeks) Everybody starts their Journals with some nice pics, right now I havent got any but will ad them soon when the babys sprout. All of us just have to be a bit patient untill we can see our babys.

Hey Since germination started i thought i might start a grow journal on this forum. Im a very satisfied ghsc grower ;-) Germinating 20x The Doctor & 3x Cheese both from GH ofc ! I will hopefully, keep the 3 Cheese and then sort out the 7 lesser potential Doctors and bin em. So my setup: SJ DR120 600w bulp + ballast & Adjust A Wings Medium reflector 1000m³ Carbon filter & 900m³ exhaust fan Davin Fancontroller with builtin thermostat 325m³ intake fan Bionair 2.4kw Bathroom heather with a manual thermostat and 2 heat settings (1.2kw & 2.4kw) Mist +3000 Humidifier 3.3liter tank & moisture output of 260ml/h Nutrients are the full B.A.C. line Wortelstimulator ( For the roots ) Bloeistimulator ( An extra boost in flowering stage ) Groeivoeding ( Nutrients for Vegitative stage ) Bloeivoeding ( Nutrients for Flowering stage ) The Final Solution ( Used to clear the soil chloor (Cl) en natrium (Na) in order to clean up the soil and let the PK booster take more effect . Only give twice, once at start of flowering and once at the end before last flush.) Plant Vitality Plus ( A general anti-stress nutrient for the plant, also helps to keep its leaves green. ) PK Booster The soil composition 150L Atami BIO Grow Mix 20L Green Label Totall Mix 50gram Mycorrhiza Will make a few picture's soon i promise ! Greetings !

Okay the weather gets better and time is running on us so it's about time we start our journal. My indoor cup aspiration has been demolished by my troubled grow @ the moment. Sorry GHSC for not competing after I had applied and started the journal! I'll be dedicated with these girls and will keep you guys updated. The remaining MM (6x) I'll use them for my new indoor grow and report that somewhere within the all mediums area on the forum. -------((Indoor I'm running an LED Spectrabox II Pro 250 Watt 10 colour Spectrum light panel, all the way this time probs, cause a possible light upgrade is issued once more and that could mean I"ll be revieuwing a dutch manufacturers LED panel along the way (they are going to send me the product for revieuw purposes) hope they will arrive before vedging the MM indoor. Or possible clones I'm going to be making from the specimen I put out. I also have my thoughts on running an other medium indoor and that is probs going to be a DWC setup))------. As this is about outdoor I've made a start with the germination GHSC style. This means the girls have had a bath in a glass off water ph 5.5 in the dark a little less than 24 hours, after that they went on a moist cottonpad and covered with moist cottonpads and plastic but no seal to have oxigen get to them, they have stayed in there a little less then 24 hours. I've been Germinating 4x Money Maker for the competition, 3 White Lemons (for tent grow and 4 Afgooey also for the tent grow, roots looked great after there preparation. And now they are places inthere starters underground. I keep my seeds in the refigurator when not used (spare, seeds) at about 7 C Celcius. They seem to sprout real fast from that change in temperature. So far all looked good except for 1 off the White Lemons. Here are the first pics. I'm working on some fancy layout for you guys like Ninja and other very respected members make cause I like those journals very mutch they get a great amount off attention witch really pays off I think! I'm going to do my best and make a GHSC worthy report on my GHSC grows, for the cup I'll be feeding with Powder Feeding off course! Till there head pops up they have an electrical controlled environment within the electrical Propagator on the pictures within this they stay @ 26 C Celsius for gemination. http://blmkb.nl/GF.mp3

I have some open space so I'm gonna do the auto cup as well I've decided to run some Kalashnikova Auto with the short flowering powder feed. Sensi cal grow for growth part of grow Sensi cal bloom for the blooming Liquid carbo Load all through flowering Superior Potash (PK 9-18) for bloom booster Technaflora Ph Up Technaflora Ph Down

Its Time for another Seedtest of Urb the Ninja.....This Time GHSC Damnesia(Amenesia x A.M.S.). I do this Seedtest together with the Money Maker test. Equipment same as usual my Homebox Xl as Flower Tent and my Ds 60 as Veg. Area. Lights Flower 400 w hps(in late stage of Flower x2) and 200w Cfl in the Veg Area. The Seed was germed 5 Days ago and cracked within 24 hrs.....after that it went into a lil baby Pod with ph regulated Coco. Today we are at Day 6 since Germination and a lil strong Damnesia is already out of the Coco.......she gets transplanted to 6l Coco tonite.I will upload some Pics after i repotted Her. So im Excited to have another GHSC Strain in my Garden and i will do my best to keep u Entertained with some gd Shots......Enjoy it Hunters.... Blessings Ninja

Konichiwa and Welcome to another Grow Journal in Ninjas Japaneese Gardens First of all i want to say Thanks to the Green House Seeds and Strain Hunters Team for giving me this Chance to make a Offical Seed Test of the Money Maker. For those who aint saw one of my other Journals over here a quick Update about the Garden Equipment and then some Words how i want to do this Seed Test. Veggie,Baby and Clones Area: Still my Cupboard Size 120x50x160cm) Lights: 400 w Metal Halide with non digital Ballast. Bulb Philips HPI-T Plus 400 W MH 30500 Lumens. Propagator:Small Sized Propagator 38x24x19 cm Pods: TEKU 7x7x6,5 cm, ca. 0,2 l Medium: Coco Flower Room:Secred Jardin Darkstreet 2 60.60x60x140cm(Update comes before the MM go into Flower) Lights: 400 w Hps with non digital Ballast(new Tent 2x 400w). Bulb(s) Osram Nav T Super 400w 55000 Lumens. Extraction: 200 cbm Charcoal Filter with 180 cbm Lti Extraction Fan. And some Clip Fans for the Air Movement. Pods: Minimum 9l in the Dr 60 max 14l in the Bigegr Tent. Medium: Coco Feeding Veg and Flower......Greenhouse Seed Co. Powder Feeding Mostly Indica/Short Flowering. No Boosters No Stimulators Nothing (except Ph + and - off course)...... Strain: Greenhouse Seed Company MONEY MAKER probably Hindu Kush x Master Kush Plan for the Seed Test: I Started 4 Seeds Today(20.2.2013) cause thats the max gd. vegged Plants that fit in my Dark Street. I will veg them at least 4-8 Weeks before they go to the Flower Tent. Lets hope for some diffrent Phenos and some Keeper Genetics. Hope all of You enjoy this Test of a New Greenhouse Strain, I will give my Best.........so far thats alll from myself enjoy some Pics of the Start Hunters. Bleesings Urban Ninja After 24 Hrs Soaking in the Glass i see One of the Money Makers is cracked and shows a lil white Roottip. Now they are between a Papertowel and a Plastic Bag is wrapped around them so it works like a Propagator/Incubator.....we will se i will make another Update before Bedtime....ps pics were shot 21.2. 3:30 pm

hi fellow growers, well after a year of seeking info and gathering supplies i decided that i will start to grow my own weed. it been a long road but i'm finally there. here are some pics from the girls. i'm in day 8 now from seed, and day 2 under 400 watts hps. and have a little problem with the humidity, can't get it higher than 55. hope i'm doing alright so far, every tip is welcome. and will be uploading once or twice a week, keep growing. bless

hey guys, i received my free package from the greenhouse, for the auto flowering world cup. and going to start my journal today. here are some pics from the goodies i received from greenhouse and some pics of the start of my first auto strain ever.

Hi guys time to start my cup journal I've decided to run some GHSC White Widow with the short flowering powder feed. Sensi cal grow for growth part of grow Sensi cal bloom for the blooming Liquid carbo Load all through flowering Superior Potash (PK 9-18) for bloom booster Technaflora Ph Up Technaflora Ph Down

Grow Journal #2 - Fully Automatic! Hi everyone, finally got the room cleaned up and ready for my second growing attempt. Going with all GHSC strains and all autoflowering strains. I would like to be able to recover some of my losses from the powdery mildew that hit 2 of my scrog plants from my last grow and thought now would be a great time to try growing some autos! So here we go Seeds: All GHSC – 3 Northern Lights Auto - 3 Sweet Mango Auto - 3 Super Critical Auto Growing media: Started in peat starter pots – will transplant directly to 12 liter pots once rooted in peat pots Pro Mix High Porosity/Grodan growcubes/Hydrotron clay pellets @ approx. 40/40/20 Lighting: Seedlings - 2 x T5 Sunblaster until ready to be transplanted and moved into tent Short veg period – 2 x T5 Sunblasters + 3 x LED (rated equivalent of 250W hps sodium each) Flower – 600W Hortilux Super HPS + 3 x LEDS Nutrients & Additives: - Reverse osmosis water+ - Seedling transplant: Botanicare ZHO (Rhizosphere root inoculant w/trichoderma & mychorrizae) - Veg: Cal Mag, DNF Veg line, DNF Enhance (pine oil additive), Advanced Nutrients B-52, potassium silicate - Flower: Cal-Mag, DNF Flowering line, DNF Enhance, potassium silicate, (maybe some Advanced Nutrients Overdrive not sure yet with them being autoflowers) Also: - Will also use CO2 producing pads - Enhance will be used as a foliar spray as well to protect against mold/mildew etc 09/10/2012 - update - 28 hours after planting seeds in jiffy’s one Super Critical sprouted so far already! - Watered one sweet mango that was drying out a bit on the bottom with 5.8 ph’d R/O with 0.30 mL/L cal-mag- (1/4 strength..since tap water has dissolved solids I wanted to give a tiny bit of what would be in tap water) - Temp in dome 27 celsius - partially opened dome now that first seed sprouted I will try and keep up on this journal best as possible being busy with school and all...I need to learn how to update without being so damn descriptive/long winded lol. Peace, happy growin & tokin

I have been looking through GHSC's website and i would like to know why are all the seeds feminized. I mean i would like to to grow my own seeds from the ones i buy and use them for the following crop. Is this because they want you to buy more each time or is it for another reason? Also just to know, how are seeds feminized?